Thank you for downloading Autodesk^® Revit^® 2014 Interoperability for Autodesk^® Inventor^® 2014 Update 1.

This readme contains the latest information regarding the installation and use of this update. It is strongly recommended that you read this entire document before you apply the update to your licensed copy of Autodesk^® Inventor^® 2014, either as a standalone product or as part of a product suite. Such as: Autodesk^® Building Design Suite 2014 Ultimate or Autodesk^® Building Design Suite 2014 Premium software. For reference, you should save this readme to your hard drive or print a copy.

Contents

• Who Should Install This Update?
• General Installation Information
• Installation Instructions
  • Apply This Update to a Stand-Alone Installation
  • Uninstall This Update

  Who Should Install This Update?

  This update is for the following Autodesk products running on all supported operating systems. Be sure to install the correct update for your software.

  Product	Update
  Autodesk Inventor 2014	RXI2014-x64_Update1.EXE (or RXI2014-x86_Update1.exe for Autodesk Inventor 2014 - 32bit)
  Autodesk Design or Creation Suites 2014	RXI2014-x64_Update1.EXE (or RXI2014-x86_Update1.exe for Autodesk Inventor 2014 - 32bit) (Note that this Update will only update the Revit 2014 Interoperability for Inventor portion of your suite product.)

  Return to Top

  General Installation Information

  Before You Begin

  As you prepare to install this update, keep the following in mind:

  Administrative Privileges

  During installation, you may be prompted for the original installation media or a network image. In order to apply this update, you must have administrative privileges to install and uninstall products.

  Product media

  Under some circumstances, you may be asked to provide the original installation source. If you installed Autodesk Inventor 2014 from the DVD or USB, you will be asked to insert the disk or USB during installation of the update. Please have the disk or USB available before starting.

  If you downloaded and installed Autodesk Inventor 2014 from the web and later deleted the extracted files (Installed by default to Program Files\Autodesk Inventor 2014\Download), the update will not be able to continue. In that case, you should follow the below procedure:

  1. Obtain the Web download file and save it to your computer.
  2. Double click the download file and allow it to extract its files, noting where they are being saved.
  3. When the Autodesk Inventor 2014 installer screen appears, click "Cancel".
  4. Continue with update installation as described in the Installation Instructions.

  Network Deployment

  Special command line switches are available for administrators. The full list can be obtained by running the update with the /? Switch.

  /q - Suppresses the completion message after this update is applied. This is useful if you use a script or batch file to apply this update to multiple computers.

  /e - Extracts the MSP file from the update executable.

  Return to Top

  Installation Instructions

  • Apply This Update to a Stand-Alone Installation
  • Uninstall This Update

  Apply This Update to a Stand-Alone Installation

  Follow these instructions to install this update on a single computer.

  1. Download the update and save it to any folder.
  2. Ensure the original product installation media is available.
  3. Find the folder where you saved the update and double-click the executable (EXE) file.
  4. When the installation is completed, the following message will be displayed: "The Update Release was successfully installed and Autodesk Revit 2014 Interoperability for Inventor has been updated."

  Return to Top

  Uninstall This Update

  Note: This update cannot be uninstalled to revert Autodesk Revit 2014 Interoperability for Inventor to its pre-update state. If you need to remove the update, please uninstall Autodesk Inventor 2014 and then reinstall it.

  Return to Top

  Copyright ^© 2013 Autodesk, Inc.