AutoCAD® Electrical 2010 Update 1 Readme

August 24th, 2009

This Readme contains the latest information regarding the installation and use of this update. It is strongly recommended that you read this entire document before you apply this update to your product. For your reference, you should save this Readme to your hard drive or print a copy.

Contents

Who Should Install This Update?
Supported Operating Systems
Information for Windows Vista Users
Primary Issues Resolved by This Update
General Installation Information
Stand-Alone Installation Instructions
Applying This Update to a Network Administrative Image
To Uninstall This Update

Who Should Install This Update?

This Update 1 is for the following Autodesk products running on all supported operating systems and languages. Be sure to install the correct update for your software.

Product

Update

AutoCAD Electrical 2010 (32-bit) Ace2010_SWL_Update1.exe
AutoCAD Electrical 2010 (64-bit) Ace2010_SWL_Update1_x64.exe

Supported Operating Systems

This update can be used with the following:

Information for Windows Vista Users

When applying this update while running AutoCAD Electrical, it is recommended that you do not click the "Automatically close applications and attempt to restart them after setup is complete" option. Instead, close AutoCAD Electrical manually before completing the installation of this update.

Primary Issues Resolved by This Update

Note: AutoCAD Electrical 2010 Update 1 includes the AutoCAD 2010 Update 1. For issues resolved by the AutoCAD 2010 Update 1, please see the appropriate update readme located on the Autodesk support web site

Circuit Builder

Insert/Edit Components/Footprints

Migration Utility

Project Database Service

Project Manager

Reports

Terminals

Wires

General Installation Information

Before You Start
As you prepare to install this update, keep these points in mind:

About Windows Command Line Switches
Two Microsoft® Windows® command line switches are built into this update:

Stand-Alone Installation Instructions

To update a stand-alone installation

  1. Download the update and save it to any folder.
  2. If required, insert the product media (for example, AutoCAD Electrical installation disc).
  3. Find the folder where you saved the update and double-click the executable (EXE) file.

Apply This Update through a Local Network
You can use Communication Center to apply this update through your local network. Detailed instructions on how to set up patching through your local network are listed in the Communication Center tab of the CAD Manager Control Utility help.

Note: The CAD Manager Control Utility can be installed from the product installation media by selecting "Install Tools and Utilities" and by then selecting the Autodesk CAD Manager Tools.

Applying This Update to a Network Administrative Image

The following distribution methods apply only to administrative images created with the Deployment Wizard. After you complete these procedures, subsequent deployments of your product will include this update.

In all cases, please "Append" this update to a deployment. The only time it is appropriate to "Merge" an update is if you intend to distribute the deployment through a group policy object.

The patch (update) file that you download contains an MSP (Microsoft Patch) file, which you extract from the executable file using the /e (extract) switch. For an example of the syntax, see step 2, below.

To add this update to a new administrative image

  1. From the Autodesk Product Support website, download the update EXE file to your local computer.
  2. On the Start menu (Windows), click Run. Enter information using the following syntax and click OK.

    <local_drive:>\<patch_name> /e <local_drive:>\< patch_name>.msp

  3. Insert the AutoCAD Electrical media and launch setup.exe.
  4. Select "Create Deployments," then click Next.
  5. On the "Begin Deployment" page, in the "Specify the Deployment Location" box, enter the shared network location where you would like to create an administrative image, or click "Browse" to find a location. Users install the product from this location.
  6. In the "Specify a Deployment Name" box, enter the name for your deployment.
  7. Continue through the Deployment Wizard, and Configure when allowed. On the "Include Service Packs" page, click "Browse" to browse to the update extracted in Step 2. Notice that the update has been added in the "Service Packs Included in this Deployment" box. Click Configuration Complete.
  8. Follow the instructions in the Deployment Wizard to complete the update deployment.

To apply this update to an existing administrative image

  1. From the Autodesk Product Support website, download the update EXE file to your local computer.
  2. On the Start menu (Windows), click Run. Enter the following information and click OK.

    <local_drive:>\<patch_name> /e <local_drive:>\< patch_name>.msp

  3. Browse to the location of the existing Administrative image.
  4. In the Tools folder, select the "Create and Modify a Deployment" shortcut.
  5. On the "Begin Deployment" page, you may change the name of the existing deployment in the "Specify the Deployment Name" box.
  6. On the "Begin Deployment page", do one of the following:
  7. Continue through the Deployment Wizard, and Configure when allowed. On the "Include Service Packs" page, click "Browse" to browse to the update extracted in Step 2. Notice that the update has been added in the "Service Packs Included in this Deployment" box. Click "Configuration Complete".
  8. Follow the instructions in the Deployment Wizard to complete the update deployment.

To Uninstall this Update

Note: This update cannot be uninstalled when the product is installed from a deployment (also called an administrative image) with a merged update.

Note: Uninstalling this update also uninstalls the AutoCAD Electrical 2010 Hotfix.

Windows XP

  1. Insert the product media.
  2. On the Start menu, click Control Panel.
  3. In the control panel, click "Add or Remove Programs".
  4. In the Add or Remove Programs window, select the Show Updates option.
  5. Find the appropriate update in the list of programs and click Remove.

Windows Vista

  1. Insert the product media.
  2. On the Windows Start menu, click Control Panel.
  3. Click Programs.
  4. Click Programs and Features.
  5. In the Programs and Features window, in the left pane, click View Installed Updates.
  6. Find the appropriate update in the list of updates and click Uninstall.

Copyright® 2009 Autodesk, Inc.