Autodesk Robot Structural Analysis Professional 2011 x64 Update Readme

Thank you for downloading Autodesk® Robot Structural Analysis Professional 2011 x64 Software Update

This readme contains the latest information regarding the installation and use of this update. It is strongly recommended that you read the entire document before you apply the update to your licensed copy of Autodesk Robot Structural Analysis Professional 2011 x64, either as a stand-alone product or as part of a suite. For reference, save this readme to your hard drive or print a copy

Contents

§  Who should install this update?

§  General Installation Information

§  Before You Begin

§  About Windows Command Line Switches

§  Installation Instructions

§  Apply This Update to a Standalone Installation

§  Apply This Update to a Network Administrative Image

§  To add this update to a new administrative image

§  To apply this update to an existing administrative image

§  To Uninstall This Update

§  Primary Issues Resolved by This Update

§  Model Definition and Analysis

§  Concrete Design

§  Steel Design

Return to Top

Who should install this update?

This update may be applied to any licensed copy of Autodesk Robot Structural Analysis Professional 2011 x64 software installed as a stand-alone product or as part of a suite.

General Installation Information

Before You Begin

As you prepare to install this update, keep these points in mind:

    Administrative Privileges

In order to apply this update, you must have administrative privileges.

    To Install This Update

This update may be run in 'silent mode' only. When started, the program either installs the content without any further user action, or refuses to run if the Autodesk Robot Structural Analysis Professional 2011 x64 software has not been installed.

    To Uninstall This Update

Note: This update cannot be uninstalled to revert Autodesk Robot Structural Analysis Professional 2011 x64 to its pre-update state. If you need to remove the update, you must first uninstall Autodesk Robot Structural Analysis Professional 2011 x64, and then reinstall it.

    Network Deployment

The Administrators can deploy this update over a network using the Deployment wizard. It is not possible to create deployment using a machine with already installed Autodesk Robot Structural Analysis Professional 2011 x64 software

About Windows Command Line Switches

Two Microsoft Windows command line switches are built into this update:
     /e - Extracts the MSP file from the update executable.
     /q - Suppresses the completion message after this update is applied. This is useful if you use a script or batch file to apply this update to multiple computers.

Instructions about how to use the /e command line switch are included in the procedures that follow.

Return to Top

Installation Instructions

Apply This Update to a Standalone Installation

Follow these instructions to install this update on a single computer.

  1. Download the update file RSAPRO2011x64SP4.exe and save it to any folder.
  2. Find the folder where you saved the update and double-click the executable (EXE) file.
  3. When the installation is completed, the following message will be displayed:
    'The Service Pack was successfully installed and Autodesk Robot Structural Analysis Professional 2011 has been updated.'

Apply This Update to a Network Administrative Image

The following distribution methods apply only to administrative images created with the Deployment wizard.

Please remember that the deployment cannot be created using machines with already installed Autodesk Robot Structural Analysis Professional 2011 software

After you complete these procedures, subsequent deployments of your product will include this update. In all cases, please 'Append' this update to a deployment. The 'Merge' method is not applicable to this update.

The patch (update) file that you download contains an MSP (Microsoft Patch) file, which has to be extracted from the executable file using the /e (extract) switch. For an example of the syntax, see step 2, below

To add this update to a new administrative image

  1. From the Autodesk Product Support website, download the update EXE file to your local computer.
  2. On the Start menu (Windows), click Run. Enter information using the following syntax and click OK.
    <local_drive:>\<patch_name> /e <local_drive:>\< patch_name>.msp
  3. Launch setup.exe from the Autodesk Robot Structural Analysis Professional 2011 installation disk/folder.
  4. Select 'Create Deployments'. Click Next.
  5. Continue through the Deployment wizard, and Configure when allowed. Accept the '64 bit deployment'. On the 'Include Service Packs' page, click 'Browse' to browse to the update extracted in Step 2. Notice that the update has been added in the 'Service Packs Included in this Deployment' box. Click 'Configuration Complete'.
  6. Follow the instructions in the Deployment wizard to complete the update deployment

To apply this update to an existing administrative image

  1. From the Autodesk Product Support website, download the update EXE file to your local computer.
  2. On the Start menu (Windows), click Run. Enter information using the following syntax and click OK.
    <local_drive:>\<patch_name> /e <local_drive:>\< patch_name>.msp
  3. Browse to the location of the existing Administrative image.
  4. In the Tools folder, select the 'Create and Modify a Deployment' shortcut.
  5. On the 'Begin Deployment' page, you may change the name of the existing deployment in the 'Specify the Deployment Name' box.
  6. On the 'Begin Deployment' page, do one of the following:
    - Select 'Create a new deployment using an existing deployment as a template'. Specify a new deployment name.
    - Select 'Modify an existing deployment'. Modify the existing deployment.
  7. Continue through the Deployment wizard, and Configure when allowed. Accept the '64 bit deployment'. On the 'Include Service Packs' page, click 'Browse' to browse to the update extracted in Step 2. Notice that the update has been added in the 'Service Packs Included in this Deployment' box. Click 'Configuration Complete'.
  8. Follow the instructions in the Deployment wizard to complete the update deployment.

To Uninstall This Update

Note: This update cannot be uninstalled to revert Autodesk Robot Structural Analysis Professional 2011 x64 to its pre-update state. If you need to remove the update, you must first uninstall Autodesk Robot Structural Analysis Professional 2011 x64, and then reinstall it.

Return to Top

Primary Issues Resolved by This Update

Model Definition and Analysis

    General

  1. Change of the layouts blocked for some operation systems-which could cause problems or crashes when opening r/c project layouts-is now possible.
  2. Offset parameter error reported while integrating Autodesk® Revit® Structure software with Autodesk Robot Structural Analysis software has been fixed.
  3. Double roundtrip between Autodesk Revit Structure software and Autodesk Robot Structural Analysis program blocked for specific configuration is possible now.

    Analysis

  1. Coefficients Fa and Fv are now updated when changing site class during seismic analysis definition for the Canadian code NBC 2005.
  2. Selfweight of the hollow slabs is now properly calculated.

Concrete Design

    General

  1. Fatal error during the definition of r/c node has been removed.

    Beams

  1. Incorrect info about the concrete volume and the reinforcement density printed on the drawings has been fixed.
  2. Fatal errors while designing beam with openings or some other beam types have been removed.

    Columns

  1. Incorrect recognition of column L-sections as T-sections during required reinforcement analysis of bars has been fixed.

    Slabs

  1. Calculation error blocking the deflection verification has been removed.
  2. API functions for managing required reinforcement analysis and results have been corrected.

Steel Design

    Steel Connections

  1. GUSSET PLATE CONNECTION-Incorrect geometry information has been updated.
  2. Wrong values of M0 and frame column height in the note results have been fixed.

    Steel Members Design

  1. CTICM rule for coefficient psi calculation for "I" shapes has been fixed.
  2. EC3-Wrong length of the third segment for internal bracings calculation has been corrected.

Return to Top

 


Autodesk, Revit, and Robot are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the right to alter product offerings and services, and specifications and pricing at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document

Occasionally, Autodesk makes statements regarding planned or future development efforts for our existing or new products and services. These statements are not intended to be a promise or guarantee of future delivery of products, services, or features but merely reflect our current plans, which may change. The Company assumes no obligation to update these forward-looking statements to reflect any change in circumstances, after the statements are made.

© 2010 Autodesk, Inc. All rights reserved.